You shut off the kitchen mixer and somewhere inside the wall, something goes thunk. Or the washing machine finishes filling and the whole house knocks. That noise is called water hammer, and while it sounds alarming, it is usually telling you something specific about your pipes, your valves or your water pressure.
We have been plumbing Gold Coast and Logan homes since 1978, and there is a local reason it comes up so often. Pressure in the City of Gold Coast’s water network can run as high as 900 kPa, while the Australian plumbing standard caps pressure at your taps at 500 kPa. Below, we explain what water hammer is, how to tell it apart from other pipe noises, where that 500 kPa rule applies, and which fixes you can legally do yourself in Queensland.
What Is Water Hammer?
Water moving through a pipe has momentum. When a valve snaps shut, that water has nowhere to go, so it stops dead and sends a pressure shockwave racing back along the pipe. The shockwave is what you hear, and if the pipe is free to move, it physically jumps against a stud, a joist or another pipe.
The spike is bigger than most people expect. The International Copper Association’s Plumbers Handbook, reproduced in Phoenix Tapware’s water hammer fact sheet, puts the shockwave from a quick-closing tap or solenoid valve at up to 3,000 kPa, and around 2,000 kPa even when only a trickle was flowing. One bang will not burst a pipe, but thousands of them load up the same joints, flexi hoses and valves until something starts to weep.
The bang also does not always come from where you are standing. Turning off the laundry tub tap can make a pipe knock inside the bathroom wall at the other end of the house.
What Causes Water Hammer in Household Pipes?
Almost every case we attend comes back to one of five things, and plenty of homes have two working together.
Quick-closing valves
Quarter-turn mixers shut off in a fraction of a second. So do the solenoid valves in washing machines, dishwashers, fridge ice makers and irrigation systems. The faster a valve closes, the harder the water stops.
High water pressure
Pressure does not cause the shockwave, but it makes every one stronger. A home at 800 kPa will bang far harder than the same home at 450 kPa. It is the most common root cause we find locally, so it gets its own section below.
Loose or unclipped pipes
Where pipe clips have broken, corroded or were never fitted properly, the pipe is free to move when the shockwave hits. Pipework under raised homes and through roof spaces is the usual suspect.
Worn tap washers and cistern valves
A worn jumper valve or washer in an older tap can flutter as water passes, giving a rapid rattle rather than a single bang. A tired float valve in a toilet cistern can do the same as it refills, often finishing with a knock.
A failing valve at the hot water system
Hot water systems have their own valves on the cold inlet, and many homes also have a tempering valve blending hot and cold before it reaches the bathroom. As these wear, they can chatter or close abruptly. Our tempering valve and thermostatic mixing valve service covers testing and replacing them.
Match the Noise to the Cause
Not every pipe noise is water hammer, and the fix depends on which one you have. Notice exactly when it happens. This is the same checklist we run through on site.
| What you hear | When it happens | Most likely cause | Who can fix it |
|---|---|---|---|
| One loud bang | Right after you shut a mixer tap | Quick-closing tap plus high pressure | Licensed plumber |
| A thud or a few bangs | When the washing machine or dishwasher stops filling | Appliance solenoid valve | Licensed plumber |
| A knock | As the toilet cistern finishes refilling | Worn float valve or float valve washer | You (washer), otherwise a plumber |
| Rapid rattle or juddering | While a tap is only partly open | Worn jumper valve or washer | You |
| Bangs at dawn with nobody awake | On a timer | Irrigation solenoid valve | You (irrigation side), otherwise a plumber |
| Humming or shuddering | With several taps running | Very high pressure or a failing pressure limiting valve | Licensed plumber |
| Ticking or creaking | As hot water runs, then as the pipes cool | Thermal expansion, not water hammer | Usually harmless |
One quick test: turn the offending mixer off slowly. If the bang disappears, the speed of the valve is the trigger and your water pressure is what makes it loud.
The 500 kPa Rule and Why Gold Coast Pipes Bang
Australian Standard AS/NZS 3500.1 sets the limit. Static water pressure at any outlet inside a building, other than a fire service outlet, must not exceed 500 kPa (clause 3.3.4 in the 2021 edition), and the national Plumbing Code of Australia applies the same ceiling to new and altered plumbing work. The Victorian plumbing regulator’s practice note on maximum static water pressure puts it plainly: if measured pressure is over 500 kPa, a pressure limiting or pressure reduction valve must be installed, and pressure above that limit can result in water hammer.
Now compare that with what arrives at your meter. The City of Gold Coast says pressure in its network can vary between 220 kPa and around 900 kPa, with homes at the bottom of a hill near a reservoir naturally sitting higher. Logan Water’s published service standard is also a minimum (210 kPa at the property connection), not a maximum. The council’s job is getting enough pressure to your boundary. Keeping it under 500 kPa inside your home happens on your side of the meter.
That is the job of a pressure limiting valve (PLV), often called a pressure reducing valve. It sits on the property side of the water meter and holds the pressure going into the house at a safe set point, and it is required wherever static pressure exceeds 500 kPa on new or altered plumbing work. The homes where we most often find pressure over the limit are:
- Older homes: the City of Gold Coast notes that buildings constructed or renovated since 2003 may have a pressure reduction valve, which leaves plenty of earlier homes without one.
- Homes with a worn-out PLV: when one fails, the house quietly goes back to full mains pressure.
Checking your pressure is easy. Screw a gauge from the hardware store onto a garden tap, turn off everything else in the house, open the tap fully and read it. Anything above 500 kPa means you either have no PLV or yours is not doing its job. Depending on how your property is plumbed, the front garden tap may sit before the valve, so if the reading looks high, try a tap closer to the house too.
What you should not do is adjust the valve yourself. The City of Gold Coast is clear that a licensed plumber is needed to repair or adjust a pressure reduction valve, and Victoria’s regulator warns that pressure above 500 kPa can void appliance warranties and property insurance.
How to Fix Water Hammer
Some fixes are quick and legal to do yourself. Others involve the water service and, in Queensland, need a licensed plumber. The line is set by the state’s list of unregulated plumbing work you can do yourself, and it is narrower than most people think.
What you can safely try yourself
- Close taps gently: easing a mixer shut slows the water down and often stops the bang altogether.
- Replace a tap washer or jumper valve: this is on the unregulated list, and it fixes most rattling taps.
- Replace a cistern float valve washer: also on the list, and the usual cure for a toilet that knocks as it refills.
- Check the irrigation system: work downstream of the irrigation isolating valve is unregulated, so you can replace a noisy solenoid or stagger your watering stations.
- Note what triggers it: which tap, which appliance, what time of day. It speeds up diagnosis.
If you would rather not pull a tap apart, our leaking taps and toilets service handles worn washers, jumper valves and cistern valves every day.
What needs a licensed plumber
- Fitting, replacing or adjusting a PLV: the most effective fix when high pressure is the root cause.
- Installing water hammer arrestors: small sealed devices with a cushion of air or gas that absorbs the shockwave. The Plumbers Handbook recommends a hammer suppression device on any water service with a quick-closing valve, and they work best fitted close to that valve.
- Re-clipping loose pipework: particularly inside walls, in roof spaces and under the house.
- Replacing worn valves: including inlet valves at the hot water system, tempering valves and mixer cartridges. Swapping a ceramic disc cartridge is not on the unregulated list, even though it feels a lot like changing a washer.
Frequently Asked Questions
Why do I suddenly have water hammer?
Something has changed. The usual culprits are a new appliance or mixer with a faster-closing valve, a pressure limiting valve that has worn out and let full mains pressure back in, or a broken pipe clip. If the noise started right after a renovation or a new dishwasher went in, look there first.
Can water hammer burst pipes?
It can, although it rarely happens in one hit. The more common outcome is gradual damage: joints that start to weep, flexi hoses that fail early and valves that wear out. A burst is more likely on older pipework or where pressure is already well over 500 kPa.
Where should a water hammer arrestor be installed?
As close as possible to the quick-closing valve causing the problem, such as the taps behind a washing machine or dishwasher. The Plumbers Handbook recommends at least one on the cold supply and one on the hot. Fitting one into the water service is not on Queensland’s unregulated list, so it is a job for a licensed plumber.
Can a hot water system cause water hammer?
Yes. Worn inlet valves, a failing tempering valve or an old pressure limiting valve near the unit can all bang or chatter. Hot pipes ticking as they heat and cool is a different noise caused by thermal expansion, and is usually harmless.
Banging Pipes on the Gold Coast or in Logan? We Can Help
If closing taps gently and replacing a washer have not quietened things down, the cause is usually pressure, a worn valve or loose pipework. We will check your static pressure, find the valve setting it off, and fix the cause rather than muffling the noise.
Charlie The Plumber has looked after homes across the Gold Coast and Logan since 1978. We are family-owned, not a franchise, and our domestic plumbing team handles everything from a rattling tap to a new pressure limiting valve. Call our Gold Coast office on (07) 5528 1414 or Logan on (07) 3444 8639, or book a job online.



